PowerTap SLOWNER’S MANUAL
4. Install Cadence Wire (Optional)Cadence can be measured via two methods, wired(pedal) and wireless (hub). To measure cadenced via thewired method
7. Verify InstallationCheck to make sure all components are properly secured. Spinthe rear wheel and verify that in the upper left hand corner of the
General Computer OperationDISPLAY LEVELSThe computer has three (3) main display levels:Top • Power Middle • Speed Bottom • Multi-FunctionDisplayNOTE:
2) Hold [MODE] or [SELECT] - a single button press and hold of either [MODE] or[SELECT] for 2 sec.3) Press [MODE] and [SELECT]- simultaneously press a
Computer NavigationPOWER FUNCTIONThe top level of the main display shows current, max, and average power readings. 1) Press [MODE] to scroll the curs
TORQUE FUNCTIONShows the torque placed on the hub in inch-pounds. To display torque in trip mode:1) Press [MODE] to scroll the cursor to the top line
SPEED FUNCTIONThe middle level of the main display shows current, max, and average speed readings. 1) Press [MODE] to scroll the cursor to the middle
MULTI-FUNCTION DISPLAYDistance (D)Total trip or the selected interval distance in interval mode is displayed in miles orkilometers from 0.00 to 999.99
Cadence (C)Cadence can be measured via two methods, wired (pedal) and wireless (hub).Wired cadence utilizes a magnet placed on the crank arm and wire
Average Cadence (C & AVG)The average cadence displays data since the last time data was cleared in tripmode or the selected interval in interval m
2CopyrightCopyright 2005. All rights reserved. No part of this publication may be copied, photographed, reproduced, translated, transmitted electronic
Heart Rate ()Current heart rate is shown up to 255 beats per minute (BMP). You must wear theheart rate chest strap to enable the heart rate measureme
Average Heart Rate (AV)This value is a running average of the heart rate in BPM. If there is no heart rateinformation this will display as 0. 1) Pres
INTERVAL MEMORY MODETo access stored interval data for the previous 9 intervals only: 1) Enter the interval mode hold [MODE] until “INT” appears on
Computer SetupThe setup feature has four (4) main modes. You do not have to complete all four to change set-tings. Please reference each mode to det
COMPUTER SETUP 1This setup menu includes: time of day, date, storage rate , wheel circumference, units of measure,odometer. NOTE: You are unable to
5) Press [SELECT] to toggle through digit values to set minutes in time ofday. Press [MODE] to save.6) Press [SELECT] to toggle through digit values
TABLE 4 - Common Wheel Circumferences9) Press [SELECT] to toggle between English or Metric units. Press [MODE] to save.10) Press [SELECT] to set star
COMPUTER SETUP 2This setup menu includes: rate of display for watts, speed, cadence, and heart rate. NOTE: You areunable to move back to a previously
6) Press [SELECT] then [MODE] to reset default settings. Press [MODE] tosave changes.COMPUTER SETUP 3This setup menu includes: zero readings for powe
5) Press [SELECT] then [MODE] to reset default settings. Press [MODE] tosave changes.COMPUTER SETUP 4This setup menu includes: sleep time, locations
3About This ManualThank you for your purchase of the CycleOps PowerTap SL. PowerTap technology is the ultimatemeasure of performance by providing real
4) The PowerTap can be used as a cycle computer or heart rate monitor.Press [SELECT] to toggle through mode options. watts, mi, and (heart icon) = po
Maintenance & SpecificationsThe following information will help you keep your PowerTap SL running properly. If you are notfamiliar with hub mainte
-Install spacers per the illustration.-Install axle.-Apply 2 grams of high quality freehub grease to the ratchet ring.-Grease the V seal and place it
COMPUTER BATTERIESThe PowerTap SL has batteries in the hub and computer. Computer batteriestypically nee d to be changed every 400 hours of use. The c
HUB BATTERIESNormal battery life in the hub is 400 hours of actual ride time. Use #357or EPX76 Silver Oxidetype batteries and always replace batteries
TEST MODE1) From the computer setup main menu press [SELECT] and scroll until the letter “t” i s flashing. Press [MODE] to enter setup mode.2) Press
6- Torque Information NOTE: The T icon is displayed.This displays information about the internal workings of the torque readings. The bottom displayis
TroubleshootingNo display on computer screen· Computer is asleep – Press [MODE] or [SELECT] on the computer to wake up the computer.· Batteries need r
· Interference with other devices - make sure you are not setting up the PowerTap inside a building with a lot of electrical noise, neon signs, or nea
GlossaryComputer - Refers to the yellow handlebar or stem mounted device.Heart Rate (HR) - This displays current HR. Max and average values are displ
Table of ContentsAbout this ManualPrecautions: Important...5System Overview...7The PowerTap System...7Preparing for Installation...7Compatibil
40Saris Cycling Group, Inc.5253 Verona RoadMadison, WI. 537111-800-783-725716034ePatents issued and pending.Patent#6,418,797POWERTAP SL COMPUTER NAVIG
Precautions: Important• Before beginning any exercise program, consult your physician.• Keep your eyes on the road. Do notbecome overly engaged with
Precautions: Important, cont.• The PowerTap wheel does not include a quick release skewer. CycleOps recommends using a steel skewer.• Both sides of
System OverviewTHE POWER TAP SYSTEMThe PowerTap system includes a power-measuring hub which measures torque and wheelspeed. This information is transm
System Overview cont.COMPATABILITYThe PowerTap SL hub is compatible with Shimano 8, 9, and 10 speed systems or Campagnolo 8,9, and 10 speed systems. F
9FIGURE 1System Overview cont.SYSTEM INSTALLATION1. Insert Wheel Into FrameInsert the PowerTap SL wheel into the frame. Make sure the axel is correct
Comments to this Manuals